Aluminum Alloy Die Casting News
Quality Improvement of Aluminum Alloy Cylinder Block Die Casts

Quality Improvement of Aluminum Alloy Cylinder Block Die Casts

  • Feb 11, 2018
  • Hits: 45

At present, people's requirement of automobiles tend to be high performance, low energy consumption and low pollution based on energy and environmental protection. There are two ways to realized t...

read more


What Kinds of Surface Treatments Do Aluminum Alloy Die Casts Have? (Part One)

What Kinds of Surface Treatments Do Aluminum Alloy Die Casts Have? (Part One)

  • Dec 22, 2017
  • Hits: 43

Surface treatment of aluminum alloy die casts can be classified into pre-treatment and post-treatment. Pre-treatment is used for removing oxide skins and oil so as to improve adhesion force of post-tr...

read more


The Common Defects of Aluminum Die Casting Parts (Part Three)

The Common Defects of Aluminum Die Casting Parts (Part Three)

  • Nov 16, 2017
  • Hits: 51

7. Segregation Features: The chemical composition at the bottom and top of the crucible is uneven during the smelting process. The die casting part which solidifies first and the die casting part that...

read more


The Common Defects of Aluminum Die Casting Parts (Part Two)

The Common Defects of Aluminum Die Casting Parts (Part Two)

  • Oct 23, 2017
  • Hits: 17

4. Inclusions Features: Inclusions are particles, whose composition is different from that of the casting, formed on the surfaces of the die casting part or inside the casting due to the coating mater...

read more


The Common Defects of Aluminum Die Casting Parts (Part One)

The Common Defects of Aluminum Die Casting Parts (Part One)

  • Oct 12, 2017
  • Hits: 57

1. Blowholes Features: First, the surfaces of the hole wall are relatively smooth with metallic luster. Second, blowholes are existing under the surfaces of the die casting parts individually or in gr...

read more


Technical Analyses of Automobile Aluminum Alloy Lower Cylinder Blocks (Part Three)

Technical Analyses of Automobile Aluminum Alloy Lower Cylinder Blocks (Part Three)

  • Sep 23, 2017
  • Hits: 19

We have X-ray inspections for die casts, and find some inner defects such as shrinkage cavities, blow holes and shrinkage porosity existing in die casts after die casts are manufactured. We put forwar...

read more


Technical Analyses of Automobile Aluminum Alloy Lower Cylinder Blocks (Part Two)

Technical Analyses of Automobile Aluminum Alloy Lower Cylinder Blocks (Part Two)

  • Sep 09, 2017
  • Hits: 15

We believe that technical key points of lower cylinder blocks are mainly as the following according to experimental analyses. 1. Scientifically design gating systems of cylinder block die casts; inse...

read more


Technical Analyses of Automobile Aluminum Alloy Lower Cylinder Blocks (Part One)

Technical Analyses of Automobile Aluminum Alloy Lower Cylinder Blocks (Part One)

  • Aug 26, 2017
  • Hits: 39

In recent years, energy saving and emission reduction has become the trend of the time and lightweight of automobile is also general trends. Under the background of the two trends, aluminum alloy mate...

read more


Five Surface Treatments for Aluminum Alloy Die Casts

Five Surface Treatments for Aluminum Alloy Die Casts

  • Aug 14, 2017
  • Hits: 14

1. Aluminum phosphating Guanidine nitrate has features of good water solubility, small amount and rapid film forming, which is an effective accelerator for aluminum phosphating. Fluoride can accelerat...

read more


Characteristics of Aluminium Die Casting and Service Lives of Dies

Characteristics of Aluminium Die Casting and Service Lives of Dies

  • Jul 29, 2017
  • Hits: 20

Characteristics of Aluminium Die Casting and Service Lives of Dies  Is it a good idea to use aluminium for die casting products? Aluminum has advantages of high thermal and electrical conduc...

read more